****** PARAMETERS *****
    2.610000     NEKTON VERSION 
            2 DIMENSIONAL RUN
          118 PARAMETERS FOLLOW
   1.00000     P001: DENSITY
  -100.000     P002: VISCOS
  0.000000E+00 P003: : BETAG
  0.000000E+00 P004: : GTHETA
  0.000000E+00 P005: : PGRADX
  0.000000E+00 P006: 
   1.00000     P007: RHOCP
   1.00000     P008: CONDUCT
  0.000000E+00 P009: 
  0.000000E+00 P010: FINTIME
   250000.     P011: NSTEPS
 -0.100000E-02 P012: DT
  0.000000E+00 P013: IOCOMM
  0.000000E+00 P014: IOTIME
   200.000     P015: IOSTEP
  0.000000E+00 P016: PSSOLVER: 0=default
   1.00000     P017: 
  0.500000E-01 P018: GRID < 0 --> # cells on screen
  -1.00000     P019: INTYPE
   7.00000     P020: NORDER
  0.100000E-06 P021: DIVERGENCE
  0.100000E-08 P022: HELMHOLTZ
  0.000000E+00 P023: NPSCAL
  0.100000E-09 P024: TOLREL
  0.100000E-04 P025: TOLABS
   1.00000     P026: COURANT/NTAU
   3.00000     P027: TORDER
  0.000000E+00 P028: TORDER: mesh velocity (0: p28=p27)
  0.000000E+00 P029: = magnetic visc if > 0, = -1/Rm if < 0
  0.000000E+00 P030: > 0 ==> properties set in uservp()
  0.000000E+00 P031: NPERT: #perturbation modes
  0.000000E+00 P032: #BCs in re2 file, if > 0
  0.000000E+00 P033: :
  0.000000E+00 P034: :
  0.000000E+00 P035: :
  0.000000E+00 P036: : XMAGNET
  0.000000E+00 P037: : NGRIDS
  0.000000E+00 P038: : NORDER2
  0.000000E+00 P039: : NORDER3
  0.000000E+00 P040: 
  0.000000E+00 P041: 1-->multiplicative SEMG
  0.000000E+00 P042: 0=gmres/1=pcg
  0.000000E+00 P043: 0=semg/1=schwarz
  0.000000E+00 P044: 0=E-based/1=A-based prec.
  0.000000E+00 P045: Relaxation factor for DTFS
  0.000000E+00 P046: reserved
  0.000000E+00 P047: vnu: mesh matieral prop.
  0.000000E+00 P048: :
  0.000000E+00 P049: :
  0.000000E+00 P050: :
  0.000000E+00 P051: 
  0.000000E+00 P052: IOHIS
  0.000000E+00 P053: 
  0.000000E+00 P054: fixed flow rate dir: |p54|=1,2,3=x,y,z
  0.000000E+00 P055: vol.flow rate (p54>0) or Ubar (p54<0)
  0.000000E+00 P056: :
  0.000000E+00 P057: :
  0.000000E+00 P058: 
  0.000000E+00 P059: !=0 --> full Jac. eval. for each el.
  0.000000E+00 P060: !=0 --> init. velocity to small nonzero
  0.000000E+00 P061: 
  0.000000E+00 P062: >0 --> force byte_swap for output
  0.000000E+00 P063: =8 --> force 8-byte output
  0.000000E+00 P064: =1 --> perturbation restart
   1.00000     P065: #iofiles (eg, 0 or 64); <0 --> sep. dirs
   4.00000     P066: output : <0=ascii, else binary
   4.00000     P067: restart: <0=ascii, else binary
  0.000000E+00 P068: iastep: freq for avg_all (0=iostep)
  0.000000E+00 P069: :           frequency of srf dump
  0.000000E+00 P070: :
  0.000000E+00 P071: :
  0.000000E+00 P072: :
  0.000000E+00 P073: 
  0.000000E+00 P074: verbose Helmholtz
  0.000000E+00 P075: :           eps for Laurette Tuckerman's
  0.000000E+00 P076: :           critical Rayleigh Number
  0.000000E+00 P077: :           sqrt Taylor number
  0.000000E+00 P078: :
  0.000000E+00 P079: :
  0.000000E+00 P080: :
  0.000000E+00 P081: :
  0.000000E+00 P082: :  p82 nxc
  0.000000E+00 P083: 
  0.000000E+00 P084: !=0 --> sets initial timestep if p12>0
  0.000000E+00 P085: dt ratio if p84 !=0, for timesteps>0
  0.000000E+00 P086: reserved
  0.000000E+00 P087: :
  0.000000E+00 P088: :  p88 1 = no prec for E
  0.000000E+00 P089: :
  0.000000E+00 P090: :
  0.000000E+00 P091: :
  0.000000E+00 P092: 
  0.000000E+00 P093: Number of previous pressure solns saved
  0.000000E+00 P094: start projecting velocity after p94 step
  0.000000E+00 P095: start projecting pressure after p95 step
  0.000000E+00 P096: :
  0.000000E+00 P097: :
  0.000000E+00 P098: 
   3.00000     P099: dealiasing: <0--> off/3--> old/4--> new
  0.000000E+00 P100: 
  0.000000E+00 P101: Number of additional modes to filter
   1.00000     P102: Dump out divergence at each time step
  0.000000E+00 P103: weight of stabilizing filter (.01)
  0.000000E+00 P104: :
  0.000000E+00 P105: :
  0.000000E+00 P106: 
  0.000000E+00 P107: !=0 --> add to h2 array in hlmhotz eqn
  0.000000E+00 P108: :
  0.000000E+00 P109: :
  0.000000E+00 P110: :
  0.000000E+00 P111: :
  0.000000E+00 P112: :
  0.000000E+00 P113: :
  0.000000E+00 P114: :
  0.000000E+00 P115: 
  0.000000E+00 P116: !=0: x elements for fast tensor product
  0.000000E+00 P117: !=0: y elements for fast tensor product
  0.000000E+00 P118: !=0: z elements for fast tensor product
      4  Lines of passive scalar data follows2 CONDUCT; 2RHOCP
   1.00000       1.00000       1.00000       1.00000       1.00000    
   1.00000       1.00000       1.00000       1.00000    
   1.00000       1.00000       1.00000       1.00000       1.00000    
   1.00000       1.00000       1.00000       1.00000    
           13  LOGICAL SWITCHES FOLLOW
  T     IFFLOW
  F     IFHEAT
  T     IFTRAN
  T F F F F F F F F F F IFNAV & IFADVC (convection in P.S. fields)
  F F T T T T T T T T T T IFTMSH (IF mesh for this field is T mesh)
  F     IFAXIS
  F     IFSTRS
  F     IFSPLIT
  F     IFMGRID
  F     IFMODEL
  F     IFKEPS
  F     IFMVBD
  T     IFCHAR
   3.33333       3.33333     -0.833333      -1.16667     XFAC,YFAC,XZERO,YZERO
 **MESH DATA** 1st line is X of corner 1,2,3,4. 2nd line is Y.