****** PARAMETERS *****
   2.6099999      NEKTON VERSION
           2  DIMENSIONAL RUN
         118  PARAMETERS FOLLOW
   1.00000     P001: DENSITY
  -100.000     P002: VISCOS
   0.00000     P003: : 	BETAG    (>0 use Boussinesq approx)
   0.00000     P004: : 	GTHETA
   0.00000     P005: :
   0.00000     P006:
   1.00000     P007: RHOCP
  -100.000     P008: CONDUCT
   0.00000     P009:
   0.00000     P010: FINTIME
  0.100000E+10 P011: NSTEPS
 -0.100000E-03 P012: DT
   0.00000     P013: IOCOMM
   0.00000     P014: IOTIME
  0.100000E+4  P015: IOSTEP
   0.00000     P016: PSSOLVER: 0=default
   0.00000     P017:
  0.250000E-01 P018: GRID < 0 --> # cells on screen
  -1.00000     P019: INTYPE
   7.00000     P020: NORDER
  0.100000E-07 P021: DIVERGENCE
  0.100000E-07 P022: HELMHOLTZ
  0              p23 NPSCAL
  0.100000E-05 P024: TOLREL
  0.100000E-09 P025: TOLABS
  0.500000     P026: COURANT/NTAU
   2.00000     P027: TORDER
   0.00000     P028: TORDER: mesh velocity (0: p28=p27)
   0.00000     P029: = magnetic visc if > 0, = -1/Rm if < 0
   0.00000     P030: > 0 ==> properties set in uservp()
   0.00000     P031: NPERT: #perturbation modes
   0.00000     P032: #BCs in re2 file, if > 0
   0.00000     P033: : S: BCs from file(s) acc. to bc.in
   0.00000     P034: :
   0.00000     P035: :
   0.00000     P036: :
   0.00000     P037: :
   0.00000     P038: :
   0.00000     P039: :
   0.00000     P040:
   0.00000     P041: 1-->multiplicative SEMG
   0.00000     P042: 0=gmres/1=pcg
   0.00000     P043: 0=semg/1=schwarz
   0.00000     P044: 0=E-based/1=A-based prec.
   0.00000     P045: Relaxation factor for DTFS
   0.00000     P046: reserved
   0.00000     P047: vnu: mesh matieral prop.
   0.00000     P048: :
   0.00000     P049: : 	mixing length factor
   0.00000     P050: :
   0.00000     P051:
   0.00000     P052: IOHIS
   0.00000     P053:
   0.00000     P054: fixed flow rate dir: |p54|=1,2,3=x,y,z
   0.00000     P055: vol.flow rate (p54>0) or Ubar (p54<0)
   0.00000     P056: :
   0.00000     P057: :
   0.00000     P058:
   0.00000     P059: !=0 --> full Jac. eval. for each el.
   0.00000     P060: !=0 --> init. velocity to small nonzero
   0.00000     P061:
   0.00000     P062: >0 --> force byte_swap for output
   0.00000     P063: =8 --> force 8-byte output
   0.00000     P064: =1 --> perturbation restart
   1.00000     P065: #iofiles (eg, 0 or 64); <0 --> sep. dirs
   6.00000     P066: output : <0=ascii, else binary
   6.00000     P067: restart: <0=ascii, else binary
   0.00000     P068: iastep: freq for avg_all (0=iostep)
   0.00000     P069: :
   0.00000     P070: :
   0.00000     P071: :
   0.00000     P072: :
   0.00000     P073:
   1.00000     P074: verbose Helmholtz
   0.00000     P075: :
   0.00000     P076: :
   0.00000     P077: :
   0.00000     P078: :  ntaupf
   0.00000     P079: :
   0.00000     P080: :
   0.00000     P081: :
   0.00000     P082: : 	dimension of coarse grid (2 -> linear
   0.00000     P083:
   0.00000     P084: !=0 --> sets initial timestep if p12>0
   0.00000     P085: dt ratio if p84 !=0, for timesteps>0
   0.00000     P086: reserved
   0.00000     P087: :
   0.00000     P088: :
   0.00000     P089: : oarse grid weighting (default=10.0)1.0
   0.00000     P090: :                amt of overlap (def.: 1
   0.00000     P091: :
   0.00000     P092:
   20.0000     P093: Number of previous pressure solns saved
   0.00000     P094: start projecting velocity after p94 step
   5.00000     P095: start projecting pressure after p95 step
   0.00000     P096: :
   0.00000     P097: : no iterative refinement 1.0
   0.00000     P098:
   3.00000     P099: dealiasing: <0--> off/3--> old/4--> new
   0.00000     P100:
   0.00000     P101: Number of additional modes to filter
   1.00000     P102: Dump out divergence at each time step
  0.500000E-01 P103: weight of stabilizing filter (.01)
   0.00000     P104: :
   0.00000     P105: :
   0.00000     P106:
   0.00000     P107: !=0 --> add to h2 array in hlmhotz eqn
   0.00000     P108: :
   0.00000     P109: :
   0.00000     P110: :
   0.00000     P111: :
   0.00000     P112: :
   0.00000     P113: :
   0.00000     P114: :
   0.00000     P115:
   0.00000     P116: !=0: x elements for fast tensor product
   0.00000     P117: !=0: y elements for fast tensor product
   0.00000     P118: !=0: z elements for fast tensor product
      4  Lines of passive scalar data follows2 CONDUCT; 2RHOCP
   1.00000       1.00000       1.00000       1.00000       1.00000
   1.00000       1.00000       1.00000       1.00000
   1.00000       1.00000       1.00000       1.00000       1.00000
   1.00000       1.00000       1.00000       1.00000
          13   LOGICAL SWITCHES FOLLOW
  T     IFFLOW
  T     IFHEAT
 T      IFTRAN
 T T T F F F F F F F F  IFNAV & IFADVC (convection in P.S. fields)
 F F T T T T T T T T T T  IFTMSH (IF mesh for this field is T mesh)
 T      IFAXIS
 F      IFSTRS
 F      IFSPLIT
 F      IFMGRID
 F      IFMODEL
 F      IFKEPS
 T      IFAZIV
 F      IFCHAR
   8.00000       8.00000     -0.500000      -4.00000     XFAC,YFAC,XZERO,YZERO
 **MESH DATA** 1st line is X of corner 1,2,3,4. 2nd line is Y.
    -2600  2       2600     NELT,NDIM,NELV
           0  PRESOLVE/RESTART OPTIONS  *****
           7          INITIAL CONDITIONS *****
C Default
C Default
C Default
C Default
C Default
C Default
C Default
  ***** DRIVE FORCE DATA ***** BODY FORCE, FLOW, Q
           4                  Lines of Drive force data follow
C
C
C
C
  ***** Variable Property Data ***** Overrrides Parameter data.
           1  Lines follow.
           0  PACKETS OF DATA FOLLOW
  ***** HISTORY AND INTEGRAL DATA *****
           0    POINTS.  Hcode, I,J,H,IEL
  ***** OUTPUT FIELD SPECIFICATION *****
           6  SPECIFICATIONS FOLLOW
 T       COORDINATES
 T       VELOCITY
 T       PRESSURE
 T       TEMPERATURE
 F       TEMPERATURE GRADIENT
           0       PASSIVE SCALARS
  ***** OBJECT SPECIFICATION *****
       0 Surface Objects
       0 Volume  Objects
       0 Edge    Objects
       0 Point   Objects