<div dir="ltr">It works fine now! It was due to the other machines /etc/hosts file... I corrected it as above, now ssh works as well ! thanks for attention, just got 2 days. But thanks to god, ©¥ know there such mathematics questions which take 40 years to solve ;)<br>
<br>have a lot of fun...<br><br>ilke<br><br><br><br><div class="gmail_quote">2008/10/7 ilke Muhtaroglu <span dir="ltr"><<a href="mailto:ilke.muhtaroglu@googlemail.com">ilke.muhtaroglu@googlemail.com</a>></span><br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div dir="ltr">Thanks for the reply,<br><br>Firewalls are both off.<br>I pass through the ssh by entering passwords and regarding the 2 bullet. <br>I can ping to both machines by name like "ping landa" and "ping linux-wyl9".<br>
Below i copy pasted my /etc/hosts file. Is there anything wrong with this? can you please detail more about the 2. issue...<br><br>ilke<br><br>------------------------<br>#<br># hosts This file describes a number of hostname-to-address<br>
# mappings for the TCP/IP subsystem. It is mostly<br># used at boot time, when no name servers are running.<br># On small systems, this file can be used instead of a<br># "named" name server.<br>
# Syntax:<br># <br># IP-Address Full-Qualified-Hostname Short-Hostname<br>#<br><br><a href="http://127.0.0.1" target="_blank">127.0.0.1</a> localhost.site localhost<br><a href="http://192.168.2.13" target="_blank">192.168.2.13</a> linux-wyl9.site linux-wyl9<br>
<a href="http://192.168.2.9" target="_blank">192.168.2.9</a> landa.site landa<br><br># special IPv6 addresses<br>::1 localhost ipv6-localhost ipv6-loopback<br><br>fe00::0 ipv6-localnet<br><br>ff00::0 ipv6-mcastprefix<br>
ff02::1 ipv6-allnodes<br>ff02::2 ipv6-allrouters<br>ff02::3 ipv6-allhosts<br>-----------------------------<div><div></div><div class="Wj3C7c"><br><br><br><br><div class="gmail_quote">On Tue, Oct 7, 2008 at 2:59 PM, The Source <span dir="ltr"><<a href="mailto:thesourcehim@gmail.com" target="_blank">thesourcehim@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">1. Disable (and stop) your firewall on both machines.<br>
2. Make sure both machines detect their proper network addresses by name (not <a href="http://127.0.0.1" target="_blank">127.0.0.1</a>)<br>
<br>
ilke Muhtaroglu ¬á¬Ú¬ê¬Ö¬ä:<div><div></div><div><br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
hi everyone,<br>
<br>
I am a new bee.<br>
<br>
I am trying to make mpich2 run on 2 linux machines. I gone through the<br>
README file and came to the point mpdboot.<br>
<br>
when i run command "mpdboot -n 2 -v -f mpd.hosts", i get the following<br>
error "failed to handshake".<br>
<br>
mpi@landa:~/mpich2-install> mpdboot -n 2 -v -f mpd.hosts<br>
running mpdallexit on landa<br>
LAUNCHED mpd on landa via<br>
RUNNING: mpd on landa<br>
LAUNCHED mpd on linux-wyl9 via landa<br>
Password:<br>
mpdboot_landa (handle_mpd_output 386): failed to handshake with mpd on<br>
linux-wyl9; recvd output={}<br>
<br>
is there any suggestion to solve this problem ?<br>
<br>
ilke<br>
</blockquote>
<br>
</div></div></blockquote></div><br></div></div></div>
</blockquote></div><br></div>